Head Gasket Slot Alignment....
Head Gasket Slot Alignment....
I had "Boiling After Engine Shutoff" (as opposed to "Unwanted Heat"), and was pretty convinced that "goop" had gummed up my head gasket slots.
According to the PO, the heads had been done during the car's refresh, but there was no denying the boiling / hot-spots in the passenger side head.
So I pulled the head, and what I found was what looks to be a significant misalignment between the slots in the gasket, and the cooling holes!
Can this possibly be the design (or an update to keep the heads at a hotter temp for emissions?), or does this look like these are the wrong gasket?
Let me know what you think. The circles in the gasket show the location of the water passages. You can see the slots are almost totally blocked, due to their position.
It looks like the passages in the heads don't align with the block.
Rocky
According to the PO, the heads had been done during the car's refresh, but there was no denying the boiling / hot-spots in the passenger side head.
So I pulled the head, and what I found was what looks to be a significant misalignment between the slots in the gasket, and the cooling holes!
Can this possibly be the design (or an update to keep the heads at a hotter temp for emissions?), or does this look like these are the wrong gasket?
Let me know what you think. The circles in the gasket show the location of the water passages. You can see the slots are almost totally blocked, due to their position.
It looks like the passages in the heads don't align with the block.
Rocky
- Attachments
-
- Driver's Head Gasket
- IMG_9215 (Large).JPG (123.88 KiB) Viewed 5400 times
-
- Hole Misalignment
- IMG_9214 (Large).JPG (204.71 KiB) Viewed 5400 times
‘71 TVR Vixen 2500 - (M Series Tribute)
'72 Interceptor III - 133/5597
'73 DeTomaso Pantera
'74 Toyota Land Cruiser FJ-40
'95 Jaguar XJS Convertible
'72 Interceptor III - 133/5597
'73 DeTomaso Pantera
'74 Toyota Land Cruiser FJ-40
'95 Jaguar XJS Convertible
-
- Posts: 433
- Joined: Mon Mar 03, 2008 1:59 pm
- Location: Dartford Moor
Re: Head Gasket Slot Alignment....
From what I have seen and read on this forum this is how they are designed to keep the temperature up for the sake of emissions, however you can open up the slots . Somebody with first hand experience will be along shortly to tell you by how much.
CHEERS BE LUCKY ALAN
Jensen 111/440/1317 /OAR 298P
Jaguar 420G
Jaguar Sovereign v8
Winnebago M/H
Jensen 111/440/1317 /OAR 298P
Jaguar 420G
Jaguar Sovereign v8
Winnebago M/H
- Steve Payne
- MASSIVE RED CARD
- Posts: 6484
- Joined: Thu Nov 17, 2005 4:51 pm
- Location: Witney , Oxfordshire
- Contact:
Re: Head Gasket Slot Alignment....
The earlier head gasket had wider slots to allow more water to flow from the block to the head, in the early 70's when emissions became a concern one of the ways they found to reduce emissions was to increase the cylinder head temperature. This with leaner fuel air ratios and it was inevitable the engines were going to have problems especially after a few years as the narrow slots started to block. I have seen some gaskets where the slots were almost completely blocked
Enlarge the slots to the pre emission level and you will notice how much cooler the engine runs. When I do this I use a Dremel and file. The width of the holes and the full length of the distance between both holes, if you use the thicker head gasket you will get the maximum of water into the head with out modifying the block.
This might make things a bit clearer.
http://members.tripod.com/mopar_roadste ... _cure.html" onclick="window.open(this.href);return false;
I would also suggest a high flow water pump and thermostat to increase the flow.
Steve
Enlarge the slots to the pre emission level and you will notice how much cooler the engine runs. When I do this I use a Dremel and file. The width of the holes and the full length of the distance between both holes, if you use the thicker head gasket you will get the maximum of water into the head with out modifying the block.
This might make things a bit clearer.
http://members.tripod.com/mopar_roadste ... _cure.html" onclick="window.open(this.href);return false;
I would also suggest a high flow water pump and thermostat to increase the flow.
Steve
JOC official Lightning engineer
Re: Head Gasket Slot Alignment....
This is my G series 383, the engine was rebuilt in 2013 and I enlarged the holes using a hole punch.
The car has now done about 20,000 miles since the rebuild and the only time it boiled over was when the fan fuse blew.
The rad and fans are original design and the only cooling system upgrades are a high flow pump and thermostat.
My car has sat in long traffic jams on some of the hottest days in UK and not overheated.
I do think fully clearing all the crud from the water jacket ( I do this with a 150 degrees C steam cleaner) and fitting a new radiator core os also key to an engine that does not overheat.
The car has now done about 20,000 miles since the rebuild and the only time it boiled over was when the fan fuse blew.
The rad and fans are original design and the only cooling system upgrades are a high flow pump and thermostat.
My car has sat in long traffic jams on some of the hottest days in UK and not overheated.
I do think fully clearing all the crud from the water jacket ( I do this with a 150 degrees C steam cleaner) and fitting a new radiator core os also key to an engine that does not overheat.
Dave Pearce
Oily Rag Classics
Jensen FF 119/133
Jensen FF 119/182
Jensen Interceptor III 128/4430
Oily Rag Classics
Jensen FF 119/133
Jensen FF 119/182
Jensen Interceptor III 128/4430
Re: Head Gasket Slot Alignment....
Thank you all for the insight.
DPP - I note that you also opened the lower holes, as well as the ones connected to the slots.
This gives me some confidence to make changes.
Appreciate the insight and experience.
Thanks -
Rocky
DPP - I note that you also opened the lower holes, as well as the ones connected to the slots.
This gives me some confidence to make changes.
Appreciate the insight and experience.
Thanks -
Rocky
‘71 TVR Vixen 2500 - (M Series Tribute)
'72 Interceptor III - 133/5597
'73 DeTomaso Pantera
'74 Toyota Land Cruiser FJ-40
'95 Jaguar XJS Convertible
'72 Interceptor III - 133/5597
'73 DeTomaso Pantera
'74 Toyota Land Cruiser FJ-40
'95 Jaguar XJS Convertible
Re: Head Gasket Slot Alignment....
I had read on a Mopar site in the past that you can make the holes too big which might cause poor cooling distribution and the rear of the engine/head gets undercooled? Hopefully someone with more knowledge can confirm or not. Obviously it works for you DPP.
When I did mine I doubled the slot width and lengthened a bit also (think it was also from the Mopar site). Has been fine also for 3 years.
Have to remember Rocky is in a really hot climate!! I lived in Phoenix for 20 years and the challenges of 45C+ days are significant.
Ray
When I did mine I doubled the slot width and lengthened a bit also (think it was also from the Mopar site). Has been fine also for 3 years.
Have to remember Rocky is in a really hot climate!! I lived in Phoenix for 20 years and the challenges of 45C+ days are significant.
Ray
MkIII Interceptor (140 8488)
- Philip Lochner
- Posts: 1254
- Joined: Thu Feb 28, 2013 12:29 am
- Location: Pretoria, South Africa
Re: Head Gasket Slot Alignment....
I also opened up those slots to the full width of the port in the block. Now I have no overheating issues on my fuel injected car.
Best regards
Philip
Mk3 7.2 #2240.9677 May '74 modified:
Fuel injected: viewtopic.php?t=15116
GM 4L60e 4-sp transmission: viewtopic.php?t=17192
Philip
Mk3 7.2 #2240.9677 May '74 modified:
Fuel injected: viewtopic.php?t=15116
GM 4L60e 4-sp transmission: viewtopic.php?t=17192
Re: Head Gasket Slot Alignment.... (Heat Riser in Intake)
As Phillip pointed out.... I live in a hot climate.
What is the collective wisdom regarding blocking off the heat riser in the intake manifold?
I did this on another American V-8 (Ford 351 Cleveland) with no issues. Legend has it that this can pick up a few horsepower by reducing the heat transfer to the intake charge.
Comments? Opinions? Fact-based Experience Descriptions?
Thanks -
Rocky
What is the collective wisdom regarding blocking off the heat riser in the intake manifold?
I did this on another American V-8 (Ford 351 Cleveland) with no issues. Legend has it that this can pick up a few horsepower by reducing the heat transfer to the intake charge.
Comments? Opinions? Fact-based Experience Descriptions?
Thanks -
Rocky
‘71 TVR Vixen 2500 - (M Series Tribute)
'72 Interceptor III - 133/5597
'73 DeTomaso Pantera
'74 Toyota Land Cruiser FJ-40
'95 Jaguar XJS Convertible
'72 Interceptor III - 133/5597
'73 DeTomaso Pantera
'74 Toyota Land Cruiser FJ-40
'95 Jaguar XJS Convertible
Re: Head Gasket Slot Alignment....
Rocky, I used the FelPro valley pan gasket with the heat riser blocked off on the last 2 head jobs I had to do. No adverse affects over 20+ years but wouldn't know if there was any actual power benefit.
FYI came across this old picture during cleaning. The Interceptor being pressed into service as a tow car after our regular tow car wrecked. Tucson Quarter Midget club at Marana in 2002.
Ray
FYI came across this old picture during cleaning. The Interceptor being pressed into service as a tow car after our regular tow car wrecked. Tucson Quarter Midget club at Marana in 2002.
Ray
- Attachments
-
- IMG_20190913_135753.jpg (174.56 KiB) Viewed 5121 times
MkIII Interceptor (140 8488)
- Philip Lochner
- Posts: 1254
- Joined: Thu Feb 28, 2013 12:29 am
- Location: Pretoria, South Africa
Re: Head Gasket Slot Alignment.... (Heat Riser in Intake)
Not sure by what is meant by "heat riser". I presume you are referring to the Exhaust Gas Recirculation channel that runs between the two banks? I blocked this off on my Interceptors as well as the 350 SBC in my C10- which also runs on a Carter TQ BTW. My EFI thread in my signature should have pics of how I modified the alu intake in this regard unless dropbox killed them as well. EDIT: I uploaded the pics to JOC. Pics here: https://www.joc.org.uk/forum/viewtopic. ... 46#p113746RockyUSA wrote:What is the collective wisdom regarding blocking off the heat riser in the intake manifold?
Living in a hot climate, I felt there is enough reason to NOT heat the intake air more than what happens anyway. If there is more horses, good. I was more interested in engine efficiency and cooler air means more dense air, ie more O2 molecules going in- which is good.
Best regards
Philip
Mk3 7.2 #2240.9677 May '74 modified:
Fuel injected: viewtopic.php?t=15116
GM 4L60e 4-sp transmission: viewtopic.php?t=17192
Philip
Mk3 7.2 #2240.9677 May '74 modified:
Fuel injected: viewtopic.php?t=15116
GM 4L60e 4-sp transmission: viewtopic.php?t=17192
Re: Head Gasket Slot Alignment....
Thanks both of you. I appreciate it and agree.
Ray – very cool picture. I just drove through Marana on my way to LA. Unfortunately, not in the Interceptor - in the Jaguar.
Rocky
Ray – very cool picture. I just drove through Marana on my way to LA. Unfortunately, not in the Interceptor - in the Jaguar.
Rocky
‘71 TVR Vixen 2500 - (M Series Tribute)
'72 Interceptor III - 133/5597
'73 DeTomaso Pantera
'74 Toyota Land Cruiser FJ-40
'95 Jaguar XJS Convertible
'72 Interceptor III - 133/5597
'73 DeTomaso Pantera
'74 Toyota Land Cruiser FJ-40
'95 Jaguar XJS Convertible