Workshop Clearance C-V8 383
- Ian Northeast
- Posts: 495
- Joined: Fri Feb 03, 2006 1:06 pm
- Location: Horley, Surrey
- Contact:
Workshop Clearance C-V8 383
Hi Guys,
I'm clearing some parts out to raise more funds for my next trip. I have images of all the following parts if anyone is interested let me know.
All the parts came from either a MK2 C-V8 or a 383 engine.
brake pedal
coil
crank damaged but regrindable
exhaust spacer
external oil filter pipes
flex plate
flex plate
front springs original
fuel tank
fuse box cover
gearbox oil cooler aftermarket part to do away with cooler inside the original radiator
handbrake cable
heater valve no idea of quality of this
hi flow water pump
kb pistons very low mileage oversize
master cylinder reservoir
new cam 440 source
new points
oil pump drive
old cams one of these is a comp cams hi perf unit (very good midrange)
original ex manifold not great but servicable
original fans
original intake manifold
original water pump
original wiper motor not sure if it still works
original heads fitted with valves and springs that have done very little work
pedal box
radio I never got it to work but then again never tried
rear bump stops
rear bumper mounts
remote oil filter plate
rockers
roller followers very little use, easy power!
ropey balancer nothing fundamentally wrong but looks rough
spare wheel carrier
std cam followers
swirl pot1 vital for fuel injection particularly if you like to play!
swirl pot2 as above but better
tacho no idea if it works (it came with the car when I bought it)
torque converter
torque converter
valves, springs and collets all low mileage
Most of the engine parts are the result of my search for more power. They have done very little work and have been replaced by bigger and better items.
The stuff left over from this advert will end up on E-bay but I'd much rather sell it to a Jensen owner.
Some of these parts are heavy, I can arrange postage but I'll get quotes first.
Ian
I'm clearing some parts out to raise more funds for my next trip. I have images of all the following parts if anyone is interested let me know.
All the parts came from either a MK2 C-V8 or a 383 engine.
brake pedal
coil
crank damaged but regrindable
exhaust spacer
external oil filter pipes
flex plate
flex plate
front springs original
fuel tank
fuse box cover
gearbox oil cooler aftermarket part to do away with cooler inside the original radiator
handbrake cable
heater valve no idea of quality of this
hi flow water pump
kb pistons very low mileage oversize
master cylinder reservoir
new cam 440 source
new points
oil pump drive
old cams one of these is a comp cams hi perf unit (very good midrange)
original ex manifold not great but servicable
original fans
original intake manifold
original water pump
original wiper motor not sure if it still works
original heads fitted with valves and springs that have done very little work
pedal box
radio I never got it to work but then again never tried
rear bump stops
rear bumper mounts
remote oil filter plate
rockers
roller followers very little use, easy power!
ropey balancer nothing fundamentally wrong but looks rough
spare wheel carrier
std cam followers
swirl pot1 vital for fuel injection particularly if you like to play!
swirl pot2 as above but better
tacho no idea if it works (it came with the car when I bought it)
torque converter
torque converter
valves, springs and collets all low mileage
Most of the engine parts are the result of my search for more power. They have done very little work and have been replaced by bigger and better items.
The stuff left over from this advert will end up on E-bay but I'd much rather sell it to a Jensen owner.
Some of these parts are heavy, I can arrange postage but I'll get quotes first.
Ian
Time flies like an arrow, but fruit flies like a banana.
Re: Workshop Clearance C-V8 383
Hello Ian, I guessing from your forum name roughly where you're based but can you clarify please?
Regards Simon
Regards Simon
2340/1842 Int Conv
1640/30077 GT
115/3215 Int MK1
Bentley 111
Mk1/Mk2 Jag
DB7 Vantage Volante
1926 Clyno Royal Saloon
1922 Aveling and Porter Steam Roller (Sally)
GPZ900R
Re: Workshop Clearance C-V8 383
Ian is from Horley in Surrey Simon, it is clarified in his Avatarinterjen wrote:Hello Ian, I guessing from your forum name roughly where you're based but can you clarify please?
Regards Simon
Manual Int&Rag-Top
"Monkey Man"sig Registrar
"Monkey Man"sig Registrar
Re: Workshop Clearance C-V8 383
Hi Ian
Are the piston 1 size over standard maybe 30thou please?
Also.. do you know what compression ratio they gave you please?
If it is easier to discuss on the phone please give me a call 07831655722.. I am only up the road in Redhill
Many thanks Ian and with my kind regards... Grant
Are the piston 1 size over standard maybe 30thou please?
Also.. do you know what compression ratio they gave you please?
If it is easier to discuss on the phone please give me a call 07831655722.. I am only up the road in Redhill
Many thanks Ian and with my kind regards... Grant
Manual Int&Rag-Top
"Monkey Man"sig Registrar
"Monkey Man"sig Registrar
- Ian Northeast
- Posts: 495
- Joined: Fri Feb 03, 2006 1:06 pm
- Location: Horley, Surrey
- Contact:
Re: Workshop Clearance C-V8 383
Hi Simon,
As Grant says I am in Horley (very near Gatwick) not that close to them there wolds!
Hi Grant,
I'll measure the pistons and send you a photo, they were fairly high compression if memory serves but I have been to sleep since then.
Might be easier if I bring them to work and you come and have a look if your down this way.
Ian
As Grant says I am in Horley (very near Gatwick) not that close to them there wolds!
Hi Grant,
I'll measure the pistons and send you a photo, they were fairly high compression if memory serves but I have been to sleep since then.
Might be easier if I bring them to work and you come and have a look if your down this way.
Ian
Time flies like an arrow, but fruit flies like a banana.
Re: Workshop Clearance C-V8 383
Hello Ian, many thanks for your reply.. Yes sure, I guess that's best if you take them to work with you and I'll wizz down, rather than measure them maybe they have a part number on them and I could work it out from there, I don't want you to go to a load of work measuring and sending pics etc.. if you let me know when they are at your shop I'll come and see you Ian .. many thanks sportIan Northeast wrote:Hi Grant,
I'll measure the pistons and send you a photo, they were fairly high compression if memory serves but I have been to sleep since then.
Might be easier if I bring them to work and you come and have a look if your down this way.
Ian
Manual Int&Rag-Top
"Monkey Man"sig Registrar
"Monkey Man"sig Registrar
- Ian Northeast
- Posts: 495
- Joined: Fri Feb 03, 2006 1:06 pm
- Location: Horley, Surrey
- Contact:
Re: Workshop Clearance C-V8 383
Ian
Time flies like an arrow, but fruit flies like a banana.
Re: Workshop Clearance C-V8 383
Do you have the engraved escutcheon for the wiper for cv8 mk 2. Know is small item but I am missing it. Tks
Re: Workshop Clearance C-V8 383
Hi Ian,
Sent you a pm.
Anton
Sent you a pm.
Anton
Re: Workshop Clearance C-V8 383
Hi Ian
I need to get a swirl pot for the SP I am putting fuel injection on - what makes and referances if any are the ones you have?
Regards
John
I need to get a swirl pot for the SP I am putting fuel injection on - what makes and referances if any are the ones you have?
Regards
John
- Ian Northeast
- Posts: 495
- Joined: Fri Feb 03, 2006 1:06 pm
- Location: Horley, Surrey
- Contact:
Re: Workshop Clearance C-V8 383
Hello John,
Ian
Either of these will work for fast road or even track use, the only reason I changed was for extra capacity (very specific to what I was doing) and ran both of these at one time or another on track.Ian
Time flies like an arrow, but fruit flies like a banana.
Re: Workshop Clearance C-V8 383
Thanks Ian,
Read that I will need one but did not appreciate the number of flow return and vent lines, I need to think this through or I’ll have fuel lines all over the place.
Regards
John
Read that I will need one but did not appreciate the number of flow return and vent lines, I need to think this through or I’ll have fuel lines all over the place.
Regards
John
-
- Posts: 17
- Joined: Wed Nov 03, 2010 5:48 pm
- Location: kent
Re: Workshop Clearance C-V8 383
Hi ,
what Radio do you have also how much of the hand break cable do you have and a price !
Regards Alan
what Radio do you have also how much of the hand break cable do you have and a price !
Regards Alan
72 Mustang soft top
66 Gardan Horizon
2002 sv8
Mk11 CV8
1970 fIAT 500
66 Gardan Horizon
2002 sv8
Mk11 CV8
1970 fIAT 500
- Ian Northeast
- Posts: 495
- Joined: Fri Feb 03, 2006 1:06 pm
- Location: Horley, Surrey
- Contact:
Re: Workshop Clearance C-V8 383
Hello Alan
The radio is a period Balupunkt but I have absolutely no idea whether it works, the wiring was such a mess behind it it is unclear whether it was the car or the radio that wasn't working. £20
I know I have the cable from the lever to the axle but will have to look whether I have the other parts to the 'calipers'. £10.
Ian
The radio is a period Balupunkt but I have absolutely no idea whether it works, the wiring was such a mess behind it it is unclear whether it was the car or the radio that wasn't working. £20
I know I have the cable from the lever to the axle but will have to look whether I have the other parts to the 'calipers'. £10.
Ian
Time flies like an arrow, but fruit flies like a banana.
Re: Workshop Clearance C-V8 383
Hi Ian do you happen to have a Cv8 spare road Wheel.
Thanks Richard.
Thanks Richard.